How to wind the fishing line on the spool inertialess. Step-by-step instruction

spinnings accessories must be properly selected for specific tasks. In this guide we will look at the nuances of proper winding fishing line. This will help avoid any unpleasant factors on fishing and disappointments. Also you will find step by step instructions on how to wind the line onto inertialess coil circuit of the attachment to the spool of fishing line and reel setup. Special secrets is not here.

How to wind the fishing line on the spool inertialess?

It would seem that everything is very simple, even the instructions for fast-response coil contains a simple circuit, so take a fishing line is wound. But this attitude is the first fishing can be completed in the form of unpleasant moments unraveling "beard" and samosbrosa loops instead of fishing. To prevent this, we have prepared material on how to wind the line onto the spool inertialess. It's not as difficult as it may seem. We will also look at how to use a fast-response coil.

winding fishing line options and a choice of fast-response spool

Usually, beginners in fishing lures begin with small light rods and the respective coils. Most often it is the size of 1500-2500 inertialless reel that can hold a 100-meter section of line 0.25-0.30 mm. In addition to size, they are different kind of winding fishing line. So, can reverse taper, straight or tapered cylindrical straight winding. If you have an inexpensive Chinese inertialless coil, then you need to be prepared for a disorderly and chaotic stacking. And if this is not critical for the normal winding fishing line, here use the cord on a reel is undesirable. After all, even the correct pre-filling with cord Buckingham does not protect against further "beards" or bad casts of tangling and overlapping tight braids. If we consider the quality lesoukladyvatel, the fishing line wound in the profile should create a straight line. Parallel to the spool, the line at the time of the cylindrical winding and sloping - during the taper. In certain models of coils, for example, "Shimano", can change the profile of the winding fishing line by installing washers under the spool. In some arrangements, in which the profile is defined by the winding bobbin taper, it can be changed by winding the backing under the main line.

How a spinning reel in the line?

Initially, put the reel on some static fixed rod (needle, a screwdriver, a pencil). You can ask someone to hold the structure. The bobbin must rotate easily. After the fishing line is threaded through a ring spinning, and make a knot at the end of it. Filling begins with attachment to the spool. Lift the handle of lesoukladyvatelya, Wrap the fishing line on the spool, tie another knot and tighten Arbor, after lower lesoukladyvatel.

If you wind the cord under the anchor point stick a band-aid, and even better here to put a piece of gum with a fingertip. So you can avoid slipping from the spool of fishing line. Then start to wind it by turning the handle evenly coil. We must not forget that during refueling the fishing line must be under tension. Tensioning is achieved by adherence bobbin. To prevent cuts, do not hold the line with his bare hands, use a piece of dense material or glove.

Backing

As used Buckingham the line sections up to 0, 30 mm. Using a large cross-section of the material can lead to further uneven winding main fishing line. It is also necessary to choose the backing of a nylon or cotton thread, they long to dry, if wet fishing. With regard to the volume of fishing line to the backing, then it can only be determined empirically. To do this we will need a second removable spool. Just as the process is as follows: first on a spare spool main fishing line is wound, after - the backing, indented a few millimeters from the side. Then the coil is attached the main spool and rewinding procedure is reversed: first the backing, and then the main fishing line. If there is no spare wheel, you will need to double-reel entire line onto a spool or any other coil.

fastening assembly of line

Fill the spool must be such that its rim to not reached about 2 mm. With this reduced friction winding fishing line on a side, it will come out during the cast freely without creating loops and knots. If the spool is rather deep, and fishing needs a volume of thin fishing line, which may fill the spool is only half or one third, under the main line is necessary to wind the old. To do this, apply the material is thinner than the head, so that eventually were not formed "bumps" and "failures". Very fast winding fishing line will lead to a "beard" during the cast.

No need to fill the spool fishing line thicker than the one on which the design is intended. A major impact on the result. Fishing lines begin to fall apart and be confused. During winding on the multiplier reel mounted sideways relative to the spool. Construction fill, short of a few millimeters up to its edges. Some multipliers better show themselves at a filled spool, but it is possible to determine only during certain operating coil or coil heaters ask around about reviews. Experienced fishermen willing to tell us how to do better. Can help and Sales.

Storage fishing line on the spool

On the question of how to wind the line onto the spool inertialess, should also clarify another point. It deals with the care of materials. In long-term storage of poorly dried scaffold lose elasticity. So, it can tear at a very important moment. To avoid this, before you remove the gear for a long time, for example, in the off-season, carefully exhaust the main line onto the floor and allow to dry. After it is necessary to return to the bobbin again. This operation is desirable to do after any fishing. In this case, a piece of fishing line can be exhausting to limit the size of a little more than he was at the far cast.