Tube - is the protection for the rods. homemade tube

For the safety of spinning during transport or storage is necessary to get a tube. And the easier it is to do with your hands, as this will reduce costs and provide an opportunity to create the most comfortable for themselves design.

The advantages of a self-made tube

Tube - this is a very convenient device for spinning storage and transport, feeder and float fishing rod. It will provide full protection rod during a fishing trip or just for storage in the pantry. And tube protects them from atmospheric precipitation, snow, rain, mud. This ensures that the rod over a long service life.

Tubes for fishing rods is a necessary thing for the experienced and avid fisherman. In addition to protection against mechanical damage, it provides ease of transportation to fishing several spinning. Tube can be purchased in almost any fishing store. But to make it on their own do not make much effort and give you the opportunity to design it to your liking.

Materials for

The most common method in the manufacture of the tube is the use of the sanitary pipe. She did not give much weight baggage is strong enough to impact and falls, and will not cause discomfort when going on a fishing trip.

Anyone can pick up the material in accordance with their preference, since each rod is individual and should take into account its size and dimensions. Before you start to make a tube with your hands, you need to prepare the necessary materials and tools. In this case, such materials are well suited:

• PVC pipe (length of which is determined by the need rods, diameter 5 cm).
• The material for processing by a.
• Foam and accessories (buttons, rivets).

For manufacturing convenience, it is necessary to have on hand tools such as a thin black marker, a ruler and a hacksaw.

The manufacturing process of

To begin with the measurement of the longest link rod. By measuring the result will need to add foam thickness of 4-6 cm As the tube -. It is safe for spinning, this material must be laid on its bottom. Instead of foam material can also be used on the sponge for washing dishes or foamed polypropylene. They also provide reliable gear.

Next, you need to take the workpiece and measure the correct length. The excess part of the need to cut down. After that, you may need to clean up this side of the fine sandpaper against scuffing. Sawn part will go to the bottom of the cover. Perfectly flat side is left to cover.

At the next step is to insert the pipe butt and see how well it is moving inside. Further it is necessary to bend the preform, so that it took the form of an oval. Thereafter butt starts to move more freely through the pipe. Therefore, the spinning is better to sit in a tube. The shape of the oval is it better to fix.

Making the cover

Turning to the manufacturing stage to cover the tube should be to make two holes on the bottom. They need to fix the cushioning material.

From the material that is available, cut a piece the size of the tube and we catch him ties. You can also put it on the glue. Then it eliminates the need for making holes in the workpiece.

At this stage you need to make a cover for the tube. It is better to take the material from the skin. Because it is necessary to cut the item to 3 mm greater than the profile of the workpiece. This is to ensure that the cover is not a failure in the case. Like parts of skin will need 2-3 pieces. They are glued together to give the desired cover thickness. It is better if it is up to 2 cm. Once all the layers are glued together, can be mounted on the lid of a small loop for convenience in its dostavaniya.

Appearance

At the final stage of product development for a spinning tube should obtyanut material. The choice of fabric for each individual. This can be both skin and jeans or a tarp.

To start sewing from the bottom cover costs. It is necessary to smoothly move along the longitudinal seam. It's worth noting that this line must be held at an angle of at least 90 degrees. Fabric with close-fitting tube should take with a reserve. This will allow the right to adjust the size of the cover.

The cloth should not hang out or to move down the operation of the tube. Therefore, it is very skin-tight material of the workpiece. And it is better to smear its silicate glue. This will promote more efficient grasp the material with extension. Finishing the seam thread kapron worth doing. you need to walk through a couple of times the fabric for better reliability. After plating is completed, the fabric and need to turn onto the pipe. When you stretch to tube should follow the seam so that it is not twisted. Only when the cover is put on the workpiece, the excess fabric can be cut. But it is recommended to leave a few centimeters for singeing. This is to ensure that the fabric does not disheveled.

At the final stage is to make the handle. Tube - is the protection for the rods. But it must also provide comfort in movement. The handle is best done from the tissue, which was used for the belts. Such a material does not stretch and is more reliable in operation. Handle length is chosen individually. It should provide comfortable movement.

After considering all the manufacturing procedure improvised tube, everyone will be able to create a similar product with their own hands.